-
Who this list is for — and who should close the tab
-
The 9-step checklist
-
Step 1: Answer 'what is a fall arrest system' before you open a catalog
-
Step 2: Read the standard code on the label, not the model name
-
Step 3: Inspect the five wear points on a full-body harness
-
Step 4: Know exactly which lanyard type you're holding
-
Step 5: Match the lanyard to the hazard, not to the job title
-
Step 6: Verify footwear certification before you trust the listing
-
Step 7: Check the compatibility chain, not just the parts
-
Step 8: Build receiving inspection — and delivery certainty — into the PO
-
Step 9: Log serials and retirement dates at the moment of receipt
-
Step 1: Answer 'what is a fall arrest system' before you open a catalog
-
Where this checklist breaks down
Who this list is for — and who should close the tab
I'm the quality and brand compliance manager at an industrial safety distributor. Roughly 200 inbound SKUs a month cross my bench — harnesses, lanyards, helmets, footwear — and I decide which ones reach customers. In Q1 2024 I rejected about 11% of first deliveries. Here's the part that surprises people: almost none of those rejections were for visible damage. They were for labeling, traceability, and mismatched standards.
This checklist is for whoever signs off on a fall protection purchase — the procurement lead, the site EHS manager, the shop owner who just got a surprise inspection notice. It's not for recreational climbers, and it isn't a substitute for hands-on training. If you're buying gear for a crew that works at height, keep reading.
Nine steps. I've ordered them the way I actually work through a lot, not the way a brochure would.
The 9-step checklist
Step 1: Answer 'what is a fall arrest system' before you open a catalog
This is the step most people skip, and it's the one that gets somebody hurt.
A fall arrest system does not prevent a fall. It stops a fall that has already started, before you hit something below. That's the whole point of the energy absorber: personal fall arrest means you're going to drop, and the system is going to catch you. Three components, always — anchor, body support (the harness), and the connecting means.
That's different from a restraint system, which physically prevents you from reaching an edge, and different again from positioning, which lets you work with hands free while your weight is on the harness. You can use the same harness across all three. You cannot use the same lanyard across all three, and that's where the mistakes live.
If your people are being told to clip a positioning lanyard into a fall arrest scenario, stop the job. Not a documentation issue. A life issue.
Step 2: Read the standard code on the label, not the model name
A Petzl harness full body model — Newton, AVAO BOD, VOLT, whichever the crew specifies — will carry either EN 361, ANSI/ASSE Z359.11, or both. Those are the two you'll see in North America and Europe, and they're the ones that matter for procurement sign-off.
If a listing shows "meets all applicable standards" with no code, I stop there and I don't come back. It's not that the product is necessarily bad. It's that I can't verify anything, and "can't verify" on a document that might get subpoenaed later is a risk I'm not taking.
Z359.11 covers full body harnesses. Z359.13 covers energy absorbers and lanyards. Two separate documents, two separate checks. I've had suppliers quote the wrong one at me more than once.
Step 3: Inspect the five wear points on a full-body harness
Thirty seconds per harness, and it catches most of what matters:
- Webbing — cuts, fraying, discoloration. UV damage shows as a faded or chalky appearance. If it looks bleached, it's been hanging in a truck bed for two summers.
- Stitching — look specifically for pulled or broken thread at the load-bearing junctions. A single broken stitch under a D-ring pad is a retirement.
- Dorsal D-ring — deformation, corrosion, or a ring that no longer sits upright on its own.
- Buckles and adjusters — they should move freely and lock positively. A buckle that slips under load isn't a buckle.
- The label — serial number, manufacture date, standard code, all legible.
Point five is the one that gets argued about. "The harness is fine, the tag just got worn off." Doesn't matter. An unreadable label means you can't establish age or service history, which means the harness is out of service. I reject more units for this than for any physical defect, and I get pushback on it every single time.
Step 4: Know exactly which lanyard type you're holding
Petzl lanyards fall into categories that look similar on a shelf and absolutely are not:
- Energy-absorbing (EN 355 / Z359.13) — deployable absorber pack that tears open during a fall. Single-use. After any fall event, it's scrap.
- Positioning (EN 358) — working lanyards that hold you at a point. Not a fall arrest device, no matter how thick it is.
- Restraint — keeps you from reaching an edge. No shock absorption, because a fall isn't supposed to happen.
That single-use rule on energy absorbers is where I've had a crew lead argue with me that the pack "barely opened." Barely opened is opened. A deployed absorber is a spent absorber, and a thermal or UV exposure question mark is enough to retire it too.
Step 5: Match the lanyard to the hazard, not to the job title
Standard nylon or polyester webbing will burn through from a single welding spatter. Not weaken — burn through. If there's hot work anywhere inside the potential fall zone, you need a Kevlar or Nomex cover on the lanyard, or you relocate the anchor so the lanyard isn't in the spatter path.
And this is where I'll be blunt: welding gloves are not a heat shield for a lanyard. I've watched a fitter drape a heavy leather welding glove over a nylon lanyard as an improvised spatter guard. In February 2023 one of those lanyards took a spatter anyway, right below the glove, and I found the burn at receiving inspection. Nobody got hurt. The crew lead's reaction was "we've done it that way for years." That's exactly the sentence I've learned to treat as a red flag.
Gloves protect hands. Covers protect webbing. Different products, different rating, no overlap.
Step 6: Verify footwear certification before you trust the listing
A lot of our customers buy work boots themselves and expense them, and plenty of that happens on Amazon. Fine. Amazon is a channel, not a certification.
What you want to see, printed inside the tongue or on a sewn-in label:
- ASTM F2413-18 (the current protective footwear standard)
- I/75 C/75 — impact and compression ratings
- Mt/75 if metatarsal protection is specified
- Manufacturer name, and the country of manufacture
If a listing for amazon safety shoes says "steel toe" with no F2413 reference anywhere, I assume the marking is absent until a photo proves otherwise. Roughly one in ten listings I've spot-checked misstates something — usually impact rating, sometimes the standard year. That's a ballpark, not a study, and it probably varies by category. But on a bulk order for a site, that uncertainty is your problem, not the seller's.
Buying from a marketplace also means the return path is you. There's no compliance desk to call. Which is fine if you planned for it and a disaster if you didn't.
Step 7: Check the compatibility chain, not just the parts
A certified harness and a certified lanyard can still be an uncertified system. Connectors need to be rated for the application, self-closing and self-locking, and sized so they don't side-load against the D-ring. Anchors need to be rated — 5,000 lb per worker under OSHA 29 CFR 1926.502(d) for the general anchor point in the US.
The failure nobody plans for is swing fall. Anchor directly above the work position, or accept that a fall is going to swing you laterally into something. That's a geometry problem, and no amount of quality inspection fixes it.
Step 8: Build receiving inspection — and delivery certainty — into the PO
Two clauses do most of the work:
One: certificates of conformity plus serial numbers, delivered with the shipment, not "on request." If they can't produce a CoC before payment, they can't produce one after an incident either.
Two: a stated ship date with a remedy attached. Not a hoped-for date. A contracted one.
Which brings me to something I've become fairly opinionated about. In March 2024 we paid a rush premium worth roughly 40% of the order value to get harnesses in ahead of a plant shutdown window. The alternative was pushing the shutdown, and the shutdown window was worth far more than the freight. I've also watched a project manager try to save $600 on expedited shipping and lose three days on a job — I don't know exactly what those days cost, but it was clearly more than $600.
The expedited freight doesn't buy you speed. It buys you a date you can plan around. When the alternative is "probably on time," I'll take the invoice every time.
Step 9: Log serials and retirement dates at the moment of receipt
Every harness gets logged on arrival: serial, model, manufacture date, receiving date, assigned user. Five minutes of data entry that saves an hour of arguing later. A harness has a service life; that clock starts at manufacture, not at purchase, which means a bargain on aged stock isn't a bargain.
If your log lives in a spreadsheet that one person maintains and nobody backs up, you don't have a log. You have a single point of failure with a person's name on it. (Note to self: this is still true at our shop and I've been meaning to fix it since last fall.)
Where this checklist breaks down
Honest caveats, because a clean list is usually a lying list.
My sample is skewed. This is built on roughly 200 mid-range industrial orders a year, plus a smaller volume of rescue and tactical gear. If you're buying for recreational climbing or for a one-person shop buying two harnesses a decade, some of these steps cost more attention than they return.
I can't speak to every market. I've worked almost entirely with North American and EU-certified supply chains. If you're sourcing from other regions, the marking conventions and the paperwork expectations shift, and I'd rather admit I don't know than pretend the checklist ports cleanly.
I don't fully understand distributor pricing on rush orders. The premiums vary so wildly between vendors for what looks like identical freight that I suspect it's more relationship than logistics. If someone has cracked that code, I'd genuinely like to hear it.
The most frustrating part of this job is still the same recurring failure: an inspection protocol documented in full, distributed to every supplier, and then a shipment arrives with the label worn off anyway. You'd think written specs would end the conversation. They don't. Interpretation varies, and the only reliable fix I've found is refusing the lot and making the cost land on the right side of the invoice.
That's the whole method, really. Read the label, check the code, inspect the five points, know your lanyard, keep heat away from webbing, verify footwear markings, check the chain, contract the date, log the serial. Nine steps, none of them clever. The value is in running all nine when you're in a hurry.